Firmware de la cámara térmica H4

Versión 3.28.0.128 – publicada el 19 de septiembre de 2019

• Versión de firmware inicial para las siguientes cámaras térmicas H4 VGA:
• 640S-H4A-THC-BO50
• 640S-H4A-THC-BO24
• 640S-H4A-THC-BO12

Versión 3.22.0.36 – publicada el 2 de febrero de 2019

• Corrige un problema con la versión 3.18.0.34 del firmware donde la cámara se podía reiniciar de manera aleatoria. Todos los usuarios deben actualizar a esta versión.

Versión 3.22.0.34 – publicada el 16 de enero de 2018

• Resuelve un problema de escalamiento de privilegios para cuentas de operador y usuario donde los comandos HTTP o CGI se ejecutan como una cuenta de administrador. Recomendamos a todos los usuarios que actualicen a esta versión. 

Versión 3.22.0.32 – publicada el 11 de diciembre de 2017

• Versión de firmware inicial para las siguientes cámaras térmicas H4 QVGA:
• 320S-H4A-THC-BO50
• 320S-H4A-THC-BO24
• 320S-H4A-THC-BO12

MIB de la cámara térmica H4

Versión 3.28.0.128 – publicada el 19 de septiembre de 2019

• Versión de Management Information Base (MIB) compatible.
• Versión de MIB para las siguientes cámaras:
• 640S-H4A-THC-BO50
• 640S-H4A-THC-BO24
• 640S-H4A-THC-BO12

Versión 3.22.0.36 – publicada el 2 de febrero de 2019

• Versión de Management Information Base (MIB) compatible.

Versión 3.22.0.34 – publicada el 16 de enero de 2018

• Versión de Management Information Base (MIB) compatible.

Versión 3.22.0.32 – publicada el 11 de diciembre de 2017

• Versión de Management Information Base (MIB) para las siguientes cámaras:
• 320S-H4A-THC-BO50
• 320S-H4A-THC-BO24
• 320S-H4A-THC-BO12

Camera Configuration Tool

Version 1.4.4.0 - Released Nov 29, 2019

Nuevas características

• In conjunction with removing default passwords on newly produced Avigilon cameras, encoders and Avigilon presence detector, CCT will not support setting an initial password on such devices.

Problemas corregidos

• Fixed an issue where the CCT may crash if configuring the analytics on a 4MP or 6MP H5A camera

Version 1.4.2.2 - Released Sept 30, 2019

Problemas corregidos

• Fixed an issue where the analytics configuration would no longer appear after a camera wasconnected to Genetec Security Center
• Fixed an issue where the inclusion area was not by default enabled when a new analytic rule iscreated.
• Bounding boxes are now appearing in the analytics configuration preview window

Version 1.4.2.0 - Released August 22, 2019

Nuevas características

• Added support for H.265.

Problemas corregidos

• Fixed an issue where the region of interest or line crossing regions for analytic events on certain cameras are rendered in a location different than the position saved on the camera. All users who have previously used CCT 1.4.0.0 to configure an area of interest or beam crossing event are recommended to use this version of CCT to double check that the configured region of interest matches the desired location.
• Removed support for fetching camera firmware from Avigilon FTP site. All Avigilon firmware has now been relocated to the Avigilon partner portal. Please see the user guide for information on how to manually download firmware and have CCT deploy the firmware updates to the cameras.
• Fixed an issue where certain cameras displayed an incorrect thumbnail preview image.
• Fixed multiple translation issues with various UI elements
• Fixed an issue where the application crashed with an unhandled exception.

Version 1.4.0.0 - Released April 4, 2019

Nuevas características

• Added support for analytic events and analytic configuration on Avigilon cameras with self-learning video analytics and Unusual Motion Detection
• Passwords are hidden during bulk setup

Problemas corregidos

• Corrected the ONVIF namespace used during camera discovery

Version 1.2.0.4 - Released November 30, 2018

Nuevas características

• Added support for H4 Multisensor camera line.

Problemas corregidos

• Fixed an issue where the tool does no display all the connected camera models under the ‘Model’ filter window if the list size exceeds the limited window size. The model filter window should now have a scroll bar functionality to display models hidden by the limited window size.
• Fixed an issue where the connected cameras are not discovered if the tool was launched when the network interface controller (NIC) was disabled and then enabled afterwards.

Problemas conocidos

• When DHCP settings are changed along with other settings, the other settings fail to apply although CCT reports the changes have succeeded.

Version 1.2.02 - Released June 10, 2016

Problemas corregidos

• Fixed an issue where changing the IP address and the names of multiple cameras at the same time causes the cameras to enter an error state.

Problemas conocidos

• CCT cannot find cameras through a specific network interface controller (NIC) if the application is launched when the NIC is disabled.
• Reinstalling the same version of CCT prompts the user to uninstall the application.
• CCT stops responding if internet connection is lost while downloading firmware from the remote repository.
• False error message is shown if Ethernet cable is disconnected from the local computer while downloading firmware from the remote repository.
• Some column headers are not displayed.

Version 1.2.0.0 - Released March 31, 2016

Nuevas características

• Update camera firmware from CCT.
• Automatically obtain latest Avigilon released firmware via CCT on command.
• Obtain and save multiple camera logs via CCT.
• Localized in the following languages: English, Chinese, French, German, Italian, Protuguese, Russian and Spanish.

Problemas corregidos

• Supports Windows 7 32-bit Operating System
• WebUI links work with IE and Edge browsers if either one is set as the default browser.
• Supports Unicode characters in export and import configuration files.
• Installer allows users to go back a step and add the tool for all users on the computer.
• Improved UI so that the offline cameras and updated fields are easier to identify.
• Fixed an issue where CCT would accept an invalid IP address in the default gateway field.
• Fixed an issue where image quality settings would not display properly if it was configured from an imported file.
• Fixed an issue with sorting newly discovered cameras so that the filters apply correctly.

Problemas conocidos

• CCT cannot find cameras through a specific network interface controller (NIC) if the application is launched when the NIC is disabled.
• Reinstalling the same version of CCT prompts the user to uninstall the application.
• CCT stops responding if the internet connection is lost while downloading firmware from the remote repository.
• False error message is shown if the Ethernet cable is disconnected from the local computer while downloading firmware from the remote repository.
• Serial number headers are not fully displayed in Russian.
• Some column headers are not displayed.

Version 1.0.0.0 - Released February 18, 2016

• Initial Avigilon Camera Configuration Tool release.