H5SL-Kamerareihe – Firmware

Version 3.32.0.38 – Veröffentlicht am 16. Dezember 2019

Neue Funktionen

• Security improvements.
• Es ist jetzt zulässig, dass der alternative Antragstellername in der Zertifikatsignieranforderung festgelegt wird.
• Added support for ethernet speed and duplex setting. The setting can be found in the Network tab under Setup on the camera's WebUI.
• Added support to enable/disable Tamper detection. The setting can be found in the Tamper Detection tab under Setup on the camera's WebUI.

Behobene Probleme

• Fixed an issue where users with operator level access are unable to configure audio settings on the camera's WebUI.
• Fixed an issue where third party VMSes such as Genetec and Milestone may show limited ability to configure the camera's frame rate.

Version 3.32.0.26 – Veröffentlicht am 20. August 2019

• Erstes Release für H5SL-Kamerareihe

H5SL-Kamerareihe – MIB

Version 3.30.0.38 – Veröffentlicht am 16. Dezember 2019

• Matching MIB release

Version 3.32.0.26 – Veröffentlicht am 20. August 2019

• Erstes Release für H5SL-Kamerareihe

Camera Configuration Tool

Version 1.4.4.0 - Released Nov 29, 2019

Neue Funktionen

• In conjunction with removing default passwords on newly produced Avigilon cameras, encoders and Avigilon presence detector, CCT will not support setting an initial password on such devices.

Behobene Probleme

• Fixed an issue where the CCT may crash if configuring the analytics on a 4MP or 6MP H5A camera

Version 1.4.2.2 - Released Sept 30, 2019

Behobene Probleme

• Fixed an issue where the analytics configuration would no longer appear after a camera wasconnected to Genetec Security Center
• Fixed an issue where the inclusion area was not by default enabled when a new analytic rule iscreated.
• Bounding boxes are now appearing in the analytics configuration preview window

Version 1.4.2.0 - Released August 22, 2019

Neue Funktionen

• Added support for H.265.

Behobene Probleme

• Fixed an issue where the region of interest or line crossing regions for analytic events on certain cameras are rendered in a location different than the position saved on the camera. All users who have previously used CCT 1.4.0.0 to configure an area of interest or beam crossing event are recommended to use this version of CCT to double check that the configured region of interest matches the desired location.
• Removed support for fetching camera firmware from Avigilon FTP site. All Avigilon firmware has now been relocated to the Avigilon partner portal. Please see the user guide for information on how to manually download firmware and have CCT deploy the firmware updates to the cameras.
• Fixed an issue where certain cameras displayed an incorrect thumbnail preview image.
• Fixed multiple translation issues with various UI elements
• Fixed an issue where the application crashed with an unhandled exception.

Version 1.4.0.0 - Released April 4, 2019

Neue Funktionen

• Added support for analytic events and analytic configuration on Avigilon cameras with self-learning video analytics and Unusual Motion Detection
• Passwords are hidden during bulk setup

Behobene Probleme

• Corrected the ONVIF namespace used during camera discovery

Version 1.2.0.4 - Released November 30, 2018

Neue Funktionen

• Added support for H4 Multisensor camera line.

Behobene Probleme

• Fixed an issue where the tool does no display all the connected camera models under the ‘Model’ filter window if the list size exceeds the limited window size. The model filter window should now have a scroll bar functionality to display models hidden by the limited window size.
• Fixed an issue where the connected cameras are not discovered if the tool was launched when the network interface controller (NIC) was disabled and then enabled afterwards.

Bekannte Probleme

• When DHCP settings are changed along with other settings, the other settings fail to apply although CCT reports the changes have succeeded.

Version 1.2.02 - Released June 10, 2016

Behobene Probleme

• Fixed an issue where changing the IP address and the names of multiple cameras at the same time causes the cameras to enter an error state.

Bekannte Probleme

• CCT cannot find cameras through a specific network interface controller (NIC) if the application is launched when the NIC is disabled.
• Reinstalling the same version of CCT prompts the user to uninstall the application.
• CCT stops responding if internet connection is lost while downloading firmware from the remote repository.
• False error message is shown if Ethernet cable is disconnected from the local computer while downloading firmware from the remote repository.
• Some column headers are not displayed.

Version 1.2.0.0 - Released March 31, 2016

Neue Funktionen

• Update camera firmware from CCT.
• Automatically obtain latest Avigilon released firmware via CCT on command.
• Obtain and save multiple camera logs via CCT.
• Localized in the following languages: English, Chinese, French, German, Italian, Protuguese, Russian and Spanish.

Behobene Probleme

• Supports Windows 7 32-bit Operating System
• WebUI links work with IE and Edge browsers if either one is set as the default browser.
• Supports Unicode characters in export and import configuration files.
• Installer allows users to go back a step and add the tool for all users on the computer.
• Improved UI so that the offline cameras and updated fields are easier to identify.
• Fixed an issue where CCT would accept an invalid IP address in the default gateway field.
• Fixed an issue where image quality settings would not display properly if it was configured from an imported file.
• Fixed an issue with sorting newly discovered cameras so that the filters apply correctly.

Bekannte Probleme

• CCT cannot find cameras through a specific network interface controller (NIC) if the application is launched when the NIC is disabled.
• Reinstalling the same version of CCT prompts the user to uninstall the application.
• CCT stops responding if the internet connection is lost while downloading firmware from the remote repository.
• False error message is shown if the Ethernet cable is disconnected from the local computer while downloading firmware from the remote repository.
• Serial number headers are not fully displayed in Russian.
• Some column headers are not displayed.

Version 1.0.0.0 - Released February 18, 2016

• Initial Avigilon Camera Configuration Tool release.